Left Continue shopping
Your Order

You have no items in your cart

FREE Shipping anywhere in EU on orders over 50€

How to Measure a Monitor for a Privacy Filter: Step Guide

How to Measure a Monitor for a Privacy Filter: Step Guide

Most people who need to measure a monitor for a privacy filter start with the number on the box. That number is where the trouble begins.

The figure printed on the packaging is a single diagonal, often rounded, and it says nothing about the width or height a filter has to cover. Two monitors sold as "24-inch" can have different viewable areas, and the outer frame, the bezel, isn't part of the picture at all.

How to find your screen size for a privacy screen

Think of this as a short monitor filter sizing guide in four steps. You measure the lit area of the screen, work out its shape, check the frame around it, and then match the result to a listed size. You need a tape measure and about five minutes.

The reason to do it this way is simple. A privacy filter that falls short of the viewable area leaves strips at the edges, and someone standing at an angle can still read what's on them. So the filter has to cover the measured area in full, and only a measurement tells you what that area is.

The method also works for fleets as well as single desks. VistaProtect has sold privacy filters since 2017 and is a trusted choice in government, education, finance and healthcare, where this kind of pre-order check is routine.

Step 1: Measure the viewable screen area, not the box size

The viewable area is the part of the panel that lights up and shows an image. Everything outside it, including the plastic frame, is bezel and doesn't count. You need two figures: edge-to-edge width and edge-to-edge height of that lit area.

Find the lit edges with a white screen

Open a blank document or a plain white web page and set it to full screen. A white display makes the boundary between lit panel and bezel obvious, which a dark desktop wallpaper doesn't.

Put the tape measure against the left lit edge and read across to the right lit edge. Write that down as your width. Then measure from the top lit edge to the bottom one for your height.

Measure in centimetres if your tape allows it, because the readings are finer. You can convert to inches at the end by dividing by 2.54.

Sketch the viewable area and check the diagonal

A quick sketch stops you mixing the two figures up. Draw a rectangle and label it like this:

        width: 52.7 cm
 +------------------------------+
 |                              |
 |      viewable area           |  height:
 |                              |  29.6 cm
 +------------------------------+

The diagonal follows from those two numbers. Square the width, square the height, add them, then take the square root. With 52.7 cm and 29.6 cm, that gives about 60.4 cm, which is 23.8 inches.

That is why a monitor sold as 24-inch can turn out to be 23.8 inches viewable. If your computed diagonal sits close to the box figure, your measuring is sound; if it's wildly off, remeasure before going any further.

Step 2: Check the aspect ratio, 16:9 or 16:10

The aspect ratio is the shape of your screen. Two monitors can share a diagonal and still be different shapes, and a filter cut for one will not suit the other.

Divide width by height to get the ratio

Take the two figures from Step 1 and divide the width by the height. A result of about 1.78 means 16:9. A result of about 1.6 means 16:10. In our sketch, 52.7 ÷ 29.6 comes to 1.78, so that screen is 16:9.

There's a quick cross-check that needs no tape measure. Open your display settings and read the native resolution: 1920 × 1080 is 16:9, while 1920 × 1200 is 16:10.

Why the same diagonal can need a different filter

A 24-inch 16:10 screen is taller than a 24-inch 16:9 screen, because the diagonal is shared but the shape isn't. A 16:10 monitor with this layout measures roughly 51.7 cm by 32.3 cm, against 53.1 cm by 29.9 cm for the 16:9 version.

VistaProtect lists 24-inch and 27-inch monitor filters separately for each ratio, so the shape matters as much as the diagonal. Fit a 16:9 filter to a 16:10 screen and you'll leave uncovered strips along the top and bottom, exactly where a neighbour can read over your shoulder.

If you only check one thing beyond the diagonal, make it this.

Step 3: Check bezel clearance before you order

Bezel clearance means looking at the band around the viewable area before you buy. A filter is sized to the lit screen, so its edge lands beside that band, and anything sitting on the band deserves a look first.

Measure the outer frame as well, from one outer edge to the other. Subtract your viewable width and halve the result, and you have the width of the bezel on each side. Do the same for height. You'll see at once how much space there is around the filter edge.

What sits on the bezel band

Run your eye and your finger around the band. Look for a webcam, an ambient light sensor, a speaker grille, a power or menu button, or a raised lip that stands proud of the panel. Make a note of each one and where it sits relative to the screen edge.

Some screens add complications. A curved panel, a raised edge or a very thin bezel can change how a filter sits, and a tape measure can't tell you that. Compare what you've found with the product page before you order, rather than assuming it will be fine.

Step 4: Match your monitor to the right privacy filter size

You now hold three facts: the measured viewable diagonal, the ratio and the state of your bezel. The chart below turns them into a size. It covers the twelve sizes in the Privacy Filters for Monitors range, which runs from 20.1-inch to 34-inch.

Privacy screen size chart for monitors

Viewable diagonal Ratio check Matching option
20.1-inch One listed option 20.1"
21.5-inch One listed option 21.5"
22-inch One listed option 22"
23-inch One listed option 23"
23.6-inch One listed option 23.6"
23.8-inch One listed option 23.8"
24-inch Width ÷ height about 1.78 24" (16:9)
24-inch Width ÷ height about 1.6 24" (16:10)
27-inch Width ÷ height about 1.78 27" (16:9)
27-inch Width ÷ height about 1.6 27" (16:10)
32-inch One listed option 32"
34-inch One listed option 34"

Privacy Filters for Monitors

Only the 24-inch and 27-inch sizes split by ratio. For every other size, match the diagonal and confirm on the product page.

This chart doesn't cover sizes the range doesn't list, such as 25-inch or 28-inch screens. If your measured diagonal lands outside 20.1 to 34 inches, or between listed sizes that aren't close, no option here will fit it.

Borderline sizes and 24-inch screens

Marketed sizes are rounded, so match the number you measured, not the number on the box. A monitor sold as 24-inch can measure 23.6 or 23.8 inches viewable, and the chart has a separate option for each of those.

When your reading falls between two listed sizes, lean towards the larger one, then check the product page for the dimensions. A filter that's too small leaves strips, and that defeats the purpose.

The 24-inch class is where most mix-ups happen, because there are four candidate options: 23.6, 23.8, 24 (16:9) and 24 (16:10). The 24-inch monitor sizing and fit guide, linked at the end of this article, goes through that case in more detail.

Each filter also carries an anti-blue light coating, so the measuring only has to be done once.

Laptops and MacBooks: measure the same way

A laptop screen is just a smaller monitor, and the same viewable-area method applies. Show a white screen, measure the lit width and height, compute the diagonal, and divide to find the ratio. The 13.3-inch and 14-inch laptop options are split into 16:9 and 16:10 versions, so the ratio check matters here too.

Once you have your figures, the Privacy Filters for Laptops listing is the place to match them. It covers sizes from 11.6-inch to 17.3-inch, including options named for Surface devices.

MacBook owners have an easier job at the matching stage. The Privacy Filters for MacBooks options are named by model and year, for example MacBook Pro 14 M1/2/3/4 (2021+), so you match your model name to the listing and use your tape measure as a double-check.

If you want buying detail beyond measurements, the MacBook privacy screen buying guide covers what to compare before you choose.

Measuring won't tell you which MacBook you own. Check that under the Apple menu on the device itself.

Avoid wrong-size returns with a pre-order check

Wrong-size orders almost always trace back to the same slip: someone trusted the box figure instead of the screen. A few minutes with a tape measure removes that risk.

Checks for single screens and fleet orders

Go through this list before you order:

  1. Measure the viewable width and height, edge to edge, on a white screen.
  2. Compute the diagonal from those two figures.
  3. Work out the ratio: about 1.78 is 16:9, about 1.6 is 16:10.
  4. Match the result to a listed option, leaning larger if you fall between two sizes.
  5. Check the bezel for a webcam, sensor, grille or raised edge.
  6. Confirm the size on the product page before you order.

If you're buying for a team, measure one sample of every monitor model before a bulk order. Marketed sizes can hide small differences between models, and one wrong assumption multiplied across a fleet is expensive to unpick.

That's the whole job. When your figures are ready, open the Privacy Filters for Monitors page and confirm your matched size there. If your screen is a borderline 24-inch, read the 24-inch monitor sizing and fit guide first.

You'll be joining a global community of users, many in regulated sectors, who rely on VistaProtect filters, and every product carries a lifetime warranty.

Frequently asked questions

Can I use the screen size on the box to buy a privacy filter?

Not on its own. The box shows one rounded diagonal, which can't tell you the width or height a filter has to cover. Measure the viewable width and height, work out the diagonal, and match that figure to the listed size.

Does the bezel count when I measure my monitor?

No. Measure only the lit area of the screen, from edge to edge. The bezel is worth measuring separately, but only to check for a webcam, sensor, speaker grille or raised edge around the screen.

How do I tell whether my monitor is 16:9 or 16:10?

Divide the viewable width by the height. About 1.78 means 16:9 and about 1.6 means 16:10. You can also open display settings: a native resolution of 1920 × 1080 is 16:9 and 1920 × 1200 is 16:10.

What happens if I buy a 16:9 filter for a 16:10 screen?

The filter will be the wrong shape. It leaves uncovered strips along the top and bottom of the screen, where someone at an angle can still read your display. For 24-inch and 27-inch monitors, pick the version that matches your ratio.

What if my measurement falls between two listed sizes?

Lean towards the larger listed size, then check the product page. A filter that falls short of the viewable area leaves strips uncovered. If the reading is nowhere near a listed size, the range from 20.1-inch to 34-inch won't have an option that fits.